Siemens PLM NX 9.0.1(3) MP03(01) Update

Missing geometry and some solids are translucency after NX to CATIA5 translation
Letter j and l not accepted in SurfaceFinishSymbol under Linux (Suse11sp1)
Surface Finish Symbol Dialog has a limitation under Linux
Assembly load options, give error SOA Client, TCV10.1.1.1 and NX 9.0.1.3
Exploding data size of new linked parts
Soa exception if NX Load Options are saved with: load file as saved
Can’t open file - get error splines with bad data detected
Unable to open some NX parts in TC managed mode, give Internal Error Memory…
Unable to load assembly prt file due to checking failed for this part
Can’t open parts The record area asked for does not exist in this object
Request Workaround for problem reported in 1975811 [see above]
Result file of ExecuteCompareReport.exe is not created correctly.
CAM Express doesn’t honor the bundle set by NX9 Licensing Tool in the Start Menu
object has no valid file root
Unable to load parts The record area asked for does not exist in this object
Fastener Assemblies in NX8.5 are not working as they did in NX7.5
Error editing a GD & T object
translator failed to read Catia V5 R23 SP2
4GD Partitions without AddContent/Remove Content don’t display Names in NX
Help with starting Cam Express NX 9.0, license error.
compiling a program in NX8.5.3 fails; works in NX8.5.0
NX does not start from Teamcenter after installing HF

Feature recognition fails for specific part
Retract Move damaged the Workpiece but NX does not realize this
CUTCOM/OFF is missing when working with retract type point
planar milling, smoothing - giving duplicate points in output
IPW Collision happened when additional Finish Pass is set in Cavity Mill
In Cavity Milling the Tool Gouge the Part
Cavity Mill error message: Put to Grid Attempted on out of range coordinate
Contour violation with transfer move in a Z-Level-operation
CAM Tool path regression on certain rough groove part
User Defined Mill Tool gives illegal instruction with 21 or more sections w/ TCM
Put to Grid Attempted… Error generating cavity mill operation
wrong value for area by using Area using Curves Analysis method
Tool gouges part during engage movement
No gouged motions found, but it exist
Put To Grid Error on ZLevel Profile
Selection filter is lost
Milling IPW Transfer not out of date
Tool with ICO+Item but without PRT File comes up with the select Template Part
Generic motion feed rate problem
Wrong calculation of milling paths using Zlevel profile
Creating Non-Orthogonal and Left Hand Coordinate Systems should not be Possible
In a Thread-Op.the Start- and End-Point of the Crest-Line missed
TDM tool search starts each time when running the FBM Create feature process
Java API accepts Datum letters not valid for DMIS in dialogs
Tool Start Position not equal when changing Cut Pattern to ZIG or ZIGZAG
mom_motion_type in WEDM-Post changed between NX7.5 and NX8.5 from Retract-Point
4-Ax WEDM Geometry and Lead In Point is wrong after update to NX8.5.3.3
BOM-View does not show any used Tool on a Sub-Carrier and Sub-Pocket (Device)
CSE turning tool simulation fails for B-head turning tool path
NX9 subtracts works different than NX6 subtracts. Problems in CAD and CAM TURNING
Error 3295016 (Error while creating spun outline) inside Simulation with RMU
NX CAM turning testcut retract position
Turning test cut mom_turn_test_cut_measuring_position
UF_CAMGEOM_append_items doesnt run with NX 8.5.3 MP3
Unable to open a NX Cam Part
GEOG - UF_CAMGEOM_append_items doesn’t run with NX 8.5.3 MP3
Turning & simulation with cutcom contact/Tracking Data is not correct
Gouge Issue in Z-LEVEL 5 Axis when Tool Offset Insertion is Defined in Holder
Holemaking - Wrong order of operations
custom attributes in tooldata for export tools disturbs NX Tool Creation
Creating Operation within a Hole Making group operations needs to be generated
CAM: Machining Feature Navigator do not show the correct Operation Status
CAM: Cannot post process after delete setup
Edit Work Section is grayed out by verifying a complete Program-Group
Attempt to save bad pointer, save aborted after replacing a subcomponent.
Internal error for Z-Level Operation
Deselect Boundary Entities
Don’t change value when I choose Inherited from Local in Part Side Stock.
Wire EDM 4-axis doesn’t follow the upper profile correct.
Update display issues when electing boundaries
Rough Offset generates a bad result with offset value over 80mm
Linked Part Module cannot be updated
Failed to open NX8.5 file in NX9.0.2
Opening CAM Template parts in NX9.0.2 fails with internal error
CAM Verify_3D-Dynamic_with 3D-Tool_assembly and Circle_Motion
Sequence shows a wrong movement
KF Adopted Composite Curve remains out-of-date when changing input curve
Bug in post builder 9.0.2
NX Partfile does not open
FASC; Radial drive method; negative stepover value locks NX and O/S
Error Put to Grid Attempted on out of range coordinate when generate toolpath
Wavy NC path generated in Cavity Mill and Zlevel in NX8.5
Wavy NC path generated in Zlevel in NX8.5
wrong result from trimming tool path
Unable to update toolpath after modify threaded hole
Engage motion does not pass along the Start/Drill Point specified.
Error difference occurs with incremental output in NX8.5
Error Put to Grid Attempted on out of range coordinate when generate toolpath
WEDM Tool path collision occurs with Roll Around.
WEDM : Tool path cannot be generated with Wire Tool.
Specifying a Lead in Point raises Encountered unexpected NULL pointer error.
Display Option Tool fails to run Verify with an error.
URG Error difference occurs with incremental output in NX8.5
Unable to open part with Internal Error: Memory access violation error message
WEDM Open Profile returns a Null Tag Error after Geometry modification.
EWCS is gone when open the file in NX8.5
Unable to open a part with error An invalid tag was passed to the tag module
Arc engage changed for Zlevel TP on cylinder from 853.3
NX report shortest tool show Unknown error when we select the check geometry
Reload List from Parent does not work.
Copy Display is grayed out when Verify is run from MB3-Tool Path.
Tool path is not generated with warning message when Lead in Distance is set 0.
Only Cut Along Wall and Floor does not work correctly.
Maximum Distance of stepover is not updated from Set Machining Data.
NX9.0.2 crashing after saving NX data which was previously created in NX7.5
Gouge Check fails to report tool gouge during rapid move
Cavity Mill operation plunges into the part during a region transfer
engage move created with add finish passes collides with the IPW
NCM Transfer using Lowest Safe Z is gouging part
gouge on lead in pass
Getting Rough cut generation failed when trying to reverse path.
saved MCS csys entitities are removed when nx4 part is open in NX7.5.5
Lock axis with right angle head fails
Spikes and irregular Engage/Retracts in a ZLevel Operation
Unable to show component if component was hidden while displaying WORKPIECE
Tool shank is gouging part in Variable Streamline operation
Local return - getting small retract/engage move when Return Move is None
Manufacturing Feature Navigator Operation Status does not present correct status
Cavity Mill; Non Cutting Linear Engage Gouges the Part
Circle/Helix moves are not linear moves in NX9.0 when 840D UDE Compressor is ON
spindle rpm variable is reset to zero
Wire EDM path generation is inconsistent.
Variable Axis-Operation will not generate after reselecting part geometry
NX8 holemilling api fails to work in NX9
Cut Level changed when copying operation from NX7554MP10 to NX9013
wire edm is throwing signal 11 when making Sequence Internal Trim
Tool database will not convert - throws signal 11
Cavity mill operation cuts too many levels at one end of the part
File opens in NX6.0.5 MP12, fails to NX8.5.3 MP3 due to CAM setup.
Corner Smoothing is inconsistent in newer versions of NX
nominal and deviation values not showing on CMM report
When running simulate machine the part turns red when check holes
Tool List ShopDocs Excel template will not create report after XLS is published
Rapid motion does not recognize the Z position of previous drill operation
Face Milling Floor Wall does not cut the faces in the order selected
Op Generate gives Memory Access Violation
NX CMM Analyze TEXT output Tolerance Detail PASSES, but individual Points FAIL.
Planar Milling produces Memory Access Violation
Old Trim Boundaries interface Remove Last wont update graphic window
Unnecessary cut region created by flowcut_ref_tool
After generating an operation the status remains as needs generation.
renaming feature does not rename relative measurement points
out of the box tool list select xlsx errors after republishing
SHOP DOCS- tool list select (HTML/Excel) order is random done from Program Order
compiling a program in NX8.5.3 fails; works in NX8.5.0
Sketch Offset Curve auto-dimension location is always on XC-YC
angularity tolerance created by LinkPMI has zero nominal value
API Example to set trim / extend amount for planar milling part boundary
planar mill part boundary cannot be removed from the operation
Fixed Contour .. area milling stepover does not update.
NX UGPART Failed To Save With Memory Access Violation
Inspector does not support the FEAT/ARC that is output when posting
getting sig 11 when linking PMI
Setting Force on Rap1 Rap2 and Rap3 is not retained after close and reopen post.
NX does not start from Teamcenter after installing NNS HF
NX9.0.3 TCIN fails to start due to TC Display Rules hiding dataset types
NX 9 crashes upon launching from TC in Kerberos SSO environment